Select the complimentary object on the layer to be aligned with the LMB then commit to the object with the RMB.
![cam350 license select cam350 license select](https://gd1.alicdn.com/imgextra/i1/487693417/TB2fMcPXWmWBuNkHFJHXXaatVXa_!!487693417.jpg)
(These layers should be CAM_DemoL1.PHO and CAM_DemoL2.PHO respectively). The layers and drills have been deliberately offset.įirst we’ll align layer 1 with layer 2 using Edit/Layers > Align. What happens to the Work Area display when you click the cursor in the Panoramic Window?.What happens in the Panoramic window when you zoom in and out?.What happens when you select Panoramic from the View menu? Change the grid using Grid Snap pull down menu.Toggle the Grid display using the “V” key.Try moving some objects using “ Grid Snap” in stead of “ Object Snap”.Use the Cam_Demo_Aligned.CAM file as a reference if you have any questions. Save your work using File/Save (the file is saved to the name you assigned with the Save As command previously in section 6) Use the “Move” command in the same way to line up the remaining partial drill layers with the rest of the layers. Move the cursor to the Destination alignment point and click once with the LMB. Remember the alignment object must be present in both the reference layer and the layer to be aligned. Place the cursor in one corner of the window and click with the LMB.ĭrag the cursor to the opposite corner and click again with the LMB.Īll selected elements that will move will become highlighted.Ĭommit to the selection by clicking the RMB (note the cursor change shape) or make a new selection as previously described.Ĭlick on the Source alignment (use the lower left tooling hole) object using the LMB. Remember: layers may be freely turned on or off to facilitate selection. Remember: to perform a netlist comparison, the CAM origin must be located in the same location as it is in the PCB design. Therefore we’ll be moving only the Board area layers (CAM_DemoNC1-4.D and Note that the lower left tooling hole of the through drill layer (CAM_DemoNC1-6.D) is already located at the origin.Press the “ W” key to select Group Mode ( Note the shape of the cursor). Note the instructions in the Command Status area of the Status Bar that will assist you in stepping through this procedure.
![cam350 license select cam350 license select](https://images.g2crowd.com/uploads/product/image/social_landscape/social_landscape_342976995d4ca8e9597a0df76d24aaf2/cam350.jpg)
Cam350 license select trial#
This might take a bit of trial and error.ħ.Now, turn on all layers except the two partial drill layers (CAM_DemoNC1-4.D and CAM_DemoNC3-4.D).įrom the Edit pull down menu select Move.
![cam350 license select cam350 license select](http://www.automation-drive.com/EX/05-14-11/arm_realview_profiler_callgraph.jpg)
You can move the components whilst their all highlighted, but best to try and get as close as possible to ultimate destination. Go to the PCB in step one and paste onto the board (right-click with mouse and board will be pasted where mouse cursor is). Select all components on the sheet (Edit | select all)Ħ. Open up one of the other PCB projects (in another instance of PCB Layout) and change the board outline into a shape (right-click outline, select convert to shape).Ĥ. This assumes you want to keep your individual board refdes numbering.ģ. Select the “Keep refdes while pasting” option from the Edit menu. Start by editing one of the PCB’s and changing the board outline dimensions to match the panel size you need (ie, something approaching your manufacturers max panel size).Ģ. I had 3 schematics, producing 3 PCB’s and wanted to combine those 3 PCB’s onto one panel to reduce manufacturing costs.ġ.
![cam350 license select cam350 license select](https://usermanual.wiki/Tp-Link/TpLinkTlSf2109PUsersManual167586.812417701/asset-d.png)
I think there’s another thread somewhere that describes this process, but if I remember correctly, it goes something like this: